STIHL MS 241 C-M Manuel d'instructions Page 10
- Page / 128
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MS 241 C-M
English
8
Keep the handles clean and dry at all
times; it is particularly important to keep
them free of moisture, pitch, oil, fuel mix,
grease or resin in order for you to
maintain a firm grip and properly control
your chain saw .
WARNING
Be sure that the guide bar and saw chain
are clear of you and all other
obstructions and objects, including the
ground. If the upper quadrant of the tip of
the bar touches any object, it may cause
kickback to occur (see section on
reactive forces). Never attempt to start
the chain saw when the guide bar is in a
cut or kerf.
For specific starting instructions, see the
appropriate section of your instruction
manual.
Starting
WARNING
To reduce the risk of fire and burn
injuries, start the engine at least 10 feet
(3 m) from the fueling spot, outdoors
only.
Start and operate your chain saw
without assistance. For specific starting
instructions, see the appropriate section
of the instruction manual. Proper starting
methods reduce the risk of injury.
WARNING
To reduce the risk of injury from saw
chain contact and / or reactive forces,
the chain brake must be engaged when
starting the chain saw. If your chain saw
is equipped with the Quickstop Plus
chain brake system, it is not sufficient to
engage that brake only for starting,
because the saw chain may begin to
rotate at high speed when the throttle
trigger lockout is depressed (releasing
the brake) in order to blip the throttle
trigger after starting.
WARNING
Do not drop start. This method is very
dangerous because you may lose
control of the chain saw.
There are two recommended methods
for starting your chain saw.
With the first recommended method, the
chain saw is started on the ground.
Make sure the chain brake is engaged
(see "Chain Brake" chapter in your
instruction manual) and place the chain
saw on firm ground or other solid surface
in an open area. Maintain good balance
and secure footing.
Grip the front handlebar of the saw firmly
with your left hand and press down. For
saws with a rear handle level with the
ground, put the toe of your right foot into
the rear handle and press down. With
your right hand pull out the starter grip
slowly until you feel a definite resistance
and then give it a brisk, strong pull.
The second recommended method for
starting your chain saw allows you to
start the saw without placing it on the
ground. Make sure the chain brake is
engaged, grip the front handle of the
chain saw firmly with your left hand.
Keep your arm on the front handle in a
locked (straight) position. Hold the rear
handle of the saw tightly between your
legs just above the knees. Maintain
good balance and secure footing. Pull
the starting grip slowly with your right
hand until you feel a definite resistance
and then give it a brisk, strong pull.
WARNING
Be sure that the guide bar and saw chain
are clear of you and all other
obstructions and objects, including the
ground. When the engine is started, the
engine speed with the starting throttle
lock engaged will be fast enough for the
clutch to engage the sprocket and, if the
chain brake is not activated, turn the saw
chain. If the upper quadrant of the tip of
the bar touches any object, it may cause
kickback to occur (see section on
reactive forces). To reduce this risk,
always engage the chain brake before
starting. Never attempt to start the chain
saw when the guide bar is in a cut or
kerf.
001BA113 KN
001BA114 KN
- STIHL MS 241 C-M 1
- Instruction Manual 2
- Manual de instrucciones 2
- 60 - 122 2
- Contents 3
- Guide to Using this Manual 4
- Safety Precautions and 5
- Working Techniques 5
- 001BA113 KN 10
- 001BA114 KN 10
- 001BA087 LÄ 11
- 001BA031 KN 12
- 001BA082 KN 12
- 001BA257 KN 15
- 001BA035 KN 16
- 001BA174 KN 17
- 001BA037 KN 19
- 001BA038 KN 20
- 001BA033 KN 20
- 001BA051 LÄ 21
- 001BA088 LÄ 22
- 001BA143 KN 23
- 001BA150 KN 23
- 001BA144 KN 24
- 001BA145 KN 24
- 001BA147 KN 24
- 001BA148 KN 25
- Cutting Attachment 27
- 533BA001 KN 28
- 143BA003 KN 28
- 142BA063 KN 29
- 142BA064 KN 29
- 001BA229 KN 30
- Chain Lubricant 32
- 001BA158 KN 33
- 143BA024 KN 33
- 143BA011 KN 34
- 143BA012 KN 34
- Winter Operation 35
- Starting / Stopping the 36
- 2410BA002 KN 37
- 241BA003 KN 37
- 2410BA020 KN 37
- 2410BA021 KN 37
- 0001BA039 KN 38
- 0001BA040 KN 38
- 001BA186 KN 38
- 0001BA041 KN 38
- Operating Instructions 39
- Oil Quantity Control 40
- Taking Care of the Guide Bar 40
- Cleaning the Air Filter 41
- Engine Management M-Tronic 42
- 2410BA019 KN 44
- Maintenance and Care 50
- Main Parts 52
- Specifications 54
- Ordering Spare Parts 55
- Maintenance and Repairs 55
- Disposal 56
- STIHL Incorporated Federal 56
- Emission Control Warranty 56
- Statement 56
- STIHL Incorporated 58
- California Exhaust and 58
- Evaporative Emissions 58
- Control Warranty Statement 58
- Trademarks 60
- Injection 61
- Contenido 62
- Acerca de este manual de 63
- Medidas de seguridad y 64
- 001BA275 KN 67
- 001BA234 KN 68
- 001BA238 KN 68
- 001BA239 KN 68
- 001BA040 KN 84
- 001BA146 KN 84
- 001BA153 KN 84
- Accesorio de corte 89
- Combustible 92
- Llenado de combustible 93
- Manejo durante el invierno 97
- Arranque / parada del motor 98
- 2410BA025 KN 99
- INDICACIÓN 100
- Instrucciones para el uso 101
- 001BA157 KN 102
- 143BA026 KN 103
- Limpieza del filtro de aire 104
- Gestión del motor 104
- 000BA039 KN 105
- Dispositivo de arranque 106
- 001BA121 KN 107
- 001BA122 KN 107
- 689BA027 KN 108
- 689BA021 KN 109
- 689BA025 KN 109
- 689BA018 KN 110
- 689BA043 KN 110
- 689BA023 KN 110
- 689BA051 KN 111
- 689BA044 KN 111
- MS 241 C-M 112
- Componentes importantes 114
- Especificaciones 116
- Pedido de piezas de 117
- Información de reparación 117
- 000BA073 KN 118
- Marcas comerciales 123
- *04587388621B* 128
Produits connexes et manuels pour Scies à chaîne STIHL MS 241 C-M
(104 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.557 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels